products

Download


FAQ

1.Why do I need all the bandwidth of category 6 cable? As far as I know, there is no application today that requires 200 MHz of bandwidth.
2.What is the general difference between category 5e and category 6?
3.Will category 6 cable supersede category 5e cable?
4.What does category 6 do for my current network vs. category 5e?
5.When should I recommend or install category 6 vs. category 5e cable? 6.What is the shortest link that the standard will allow?
7.What is a ¡°tuned¡± system between cable and hardware? Is this really needed if product meets the standard?
8.What is impedance matching between cable and hardware? Is this really needed if product meets the standard?
9.Is there a use for category 6 cable in the residential market?
10.Why wouldn¡¯t I skip category 6 and go straight to optical fiber?¡¡¡¡11.What is meant by the term "Electrically Balanced"?
12.What is the difference between enhanced category 5e cable rated for 400 MHz and category 6 cable rated for 250 MHz?
13.Why did all category 6 cable used to have a spline, and now is offered without one?
14.Is there a limitation on the size of bundles one can have with category 6 cable? Can you have 200-300 and still pass category 6 cable?
15.Will contractors be able to make their own patch cords?
16.Do you have to use the manufacturer¡¯s patch cords to get category 6 cable performance?
17.Why do field tester manufacturers offer many different link adapters if everyone meets the standard?
18.Would you get passing test results if you used a link adapter not recommended by a manufacturer?
19.Is there any product categorization for Category 5e cabling and Category 6 cabling? Are the connectors for Category 5e cable and Category 6 cable different? Why are they more expensive?
20.What will happen if I mix and match different manufacturers' hardware together?

  • faq:

1: What is Structured cabling system?
2: What are the major components of a Structured cabling system?
3: Why do we use Wall Jacks?
4: Why do we use Patch Panel?
5: Why do we use 110 punchdown block?
6: Why do we use hub?
7: Why do we use Patch Cables?
8: What is 568A standard?
9: What is Category 5 cable?
10: What is Cate 5e cable?
11: What is Category 6 & 7?
12: What is Power Sum?
13: Why do we use Category 6 instead of Enhanced Category 5 Products?
14: What is Unshielded Twisted Pair( UTP) Cable?
15: What is the major UTP cable Categories?
16: What is Screened Twisted Pair Cables (FTP / ScTP)?
17: What is Shielded Twisted Pair Cables (STP)?
18: What is Coaxial Cables?
19: What is Thicknet?
20: What is Thinnet?
21: What is CATV cables?
22: What is Twinaxial cables?
23: What is Fiber Optics Cable?
24: What is Multi-Mode Fiber Cables?
25: What is Single-Mode Fiber?
26: What is RJ-45 connector?
27: What is IBM Cabling System?
28: What is Patch cord bending radius?
29: What is Plenum/Non-Plenum cable?
30: What is the installation distance?
31: What is 568B wiring configuration?
32: What is a Demarc?
33: What is Cable Topology?
34: What is Daisy Chain Topology?
35: What is bus Topology?
36: What is a Star Topology?
37: What is an MDF and an IDF?
38: What is the difference between different wiring configuration?
39: Why are the pairs shuffled around, instead of laid out logically?
40: When I should use 568A or 568B or USOC?
41: When is Wireless going to replace cabling?
42: What's the difference between T568A and T568B wiring schemes?
43: What is the minimum separation distance required between power and communication cables?
44: Is there a difference between shielded and screened cable?
45: There has been some concern recently about 'short link resonance'.What is it?
46: What is component compliance for Cat 6 product?
47: What is backwards compatibility?
48: If component compliance is required in Category 6 standard, why are most system offer link and channel compliant products?
49:Why do I need all the bandwidth of category 6? As far as I know, there is no application today that requires 200 MHz of bandwidth.
50:What is the general difference between category 5e and category 6?
51: Will category 6 supersede category 5e?
52: What does category 6 do for my current network vs. category 5e?
53:When should I recommend or install category 6 vs. category 5e?
54:What is the shortest link that the standard will allow?

Cabling System Manufacturer and a Cabling Solution Provider


Company Profile | Distribution Policy | Products | Business Partners | Contact | links | link us | FAQ | News | site map | download
Copyright © 1991-2004 Addison Technology Ltd
webmaster@addison-tech.com